Safety
All operations described in this user manual must be carried out in compliance with safety standards under the responsibility of a competent authority.
To access installed capacitors:
Switch off main power supply.
Switch off power supply control circuit.
Allow capacitor discharge time(1 minute).
Short circuit and earth the terminals to ensure that capacitoirs are fully discharged.
Caution: Do not touch the capacitor terminals before discharging.
Cylinder Capacitor Attention
Wrong selection of capacitor with respect to duty to be performedwill cause over heating. over stress, and it shortens the life ofcapacitor and hence user should take proper care for selectionof capacitor and maintain the operating conditions.
Cable Cross Section selection table
kvar Rating | Cable size in mm2 |
|||||
230V/240V | 400 to 480V |
>600V |
||||
Al | Cu | Al | Cu | Al | Cu |
|
5 | 6 | 6 | 6 | 6 | 6 | 6 |
7.5 | 10 | 6 | 6 | 6 | 6 | 6 |
10 | 16 | 10 | 6 | 6 | 6 | 6 |
12.5 | 10 | 6 | 6 | 6 | ||
15 | 10 | 6 | 6 | 6 | ||
20 | 16 | 10 | 10 | 6 | ||
25 | 25 | 16 | 15 | 10 | ||
30 | - | 25 | 15 | 10 | ||
40 | - | 35 | 25 | 16 | ||
50 | - | 35 | 35 | 25 |
Overall Dimension
Main Spesificasions & Case Dimension
Model BGMJ | Rated voltage (kV) | Rated output (kvar) | Total capacitance (μF) | Rated current (A) | Case Dimension DxH(mm) | Base Screw for Installation M xH(mm) | Figure |
0.4-3-3 | 0.4 | 3 | 60 | 4.3 | φ76x135 | M12x16 | Y1 |
0.4-4-3 | 0.4 | 4 | 80 | 5.8 | φ76x 180 | M12x16 | Y1 |
0.4-5-3 | 0.4 | 5 | 99 | 7.2 | φ76x180 | M12x 16 | Y1 |
0.4-6-3 | 0.4 | 6 | 119 | 8.7 | φ76x180 | M12x16 | Y1 |
0.4-7.5-3 | 0.4 | 7.5 | 149 | 10.8 | φ76x180 | M12x 16 | Y1 |
0.4-10-3 | 0.4 | 10 | 199 | 14.4 | φ76x240 | M12x16 | Y1 |
0.4-12-3 | 0.4 | 12 | 239 | 17.3 | φ76x240 | M12x16 | Y1 |
0.4-14-3 | 0.4 | 14 | 279 | 20.2 | φ76x280 | M12x16 | Y1 |
0.4-15-3 | 0.4 | 15 | 298 | 21.7 | φ76x280 | M12x 16 | Y1 |
0.4-16-3 | 0.4 | 16 | 318 | 23.1 | φ86x280 | M12x16 | Y1 |
0.4-18-3 | 0.4 | 18 | 358 | 26.0 | φ86x280 | M12x16 | Y1 |
0.4-20-3 | 0.4 | 20 | 398 | 28.9 | φ86x280 | M12x 16 | Y1 |
0.4-25-3 | 0.4 | 25 | 497 | 36.1 | φ106x280 | M16x25 | Y1 |
0.4-30-3 | 0.4 | 30 | 597 | 43.3 | φ116x280 | M16x25 | Y1 |
0.45-3-3 | 0.45 | 3 | 47.2 | 3.8 | φ76x135 | M12x16 | Y1 |
0.45-4-3 | 0.45 | 4 | 62.9 | 5.1 | φ76x180 | M12x16 | Y1 |
0.45-5-3 | 0.45 | 5 | 78.6 | 6.4 | φ76x180 | M12x16 | Y1 |
0.45-6-3 | 0.45 | 6 | 94.4 | 7.7 | φ76x180 | M12x 16 | Y1 |
0.45-7.5-3 | 0.45 | 7.5 | 118 | 9,6 | φ76x180 | M12x16 | Y1 |
0.45-10-3 | 0.45 | 10 | 157 | 12.8 | φ76x240 | M12x16 | Y1 |
0.45-12-3 | 0.45 | 12 | 189 | 15.4 | φ76x240 | M12x16 | Y1 |
0.45-14-3 | 0.45 | 14 | 220 | 18.0 | φ76x280 | M12x 16 | Y1 |
0.45-15-3 | 0.45 | 15 | 236 | 19.2 | φ76x280 | M12x16 | Y1 |
0.45-16-3 | 0.45 | 16 | 252 | 20.5 | φ86x280 | M12x16 | Y1 |
0.45-18-3 | 0.45 | 18 | 283 | 23.1 | φ86x280 | M12x16 | Y1 |
0.45-20-3 | 0.45 | 20 | 314 | 25.7 | φ86x280 | M12x 16 | Y1 |
0.45-25-3 | 0.45 | 25 | 393 | 32.1 | φ106x280 | M16x25 | Y1 |
0.45-30-3 | 0.45 | 30 | 472 | 38.5 | φ116x280 | M16x25 | Y1 |
http://www.jiukang.com/